The Autoflush can be used with Pi’s pH, ORP, free chlorine, total chlorine, ozone and chlorine dioxide sensors (or a combination of sensors) and consists of a large flow cell that automatically empties on a user selectable time basis. The signal from the sensor is held and the whole flow cell including the sensor(s) is flushed with clean water. For the original customer this meant a new pH sensor after 18 months rather than sooner, resulting in a significant improvement in process control and a very significant saving in pH sensors. Since then many customers have taken advantage of the Autoflush and it is installed around the world in paper mills, food factories and other plant where keeping the sensors clean enhances their performance.
| Document | Type | Size |
|---|---|---|
Autoflush
| Brochure | 411kB |
Focus Ons are a series of short articles distributed by email providing technical information regarding instrumentation, process measurement in potable, waste, process and pool waters. If you would like to join the mailing list, please contact us.
Many different sites ranging across the whole water industry have a daily struggle to keep instrumentation functioning correctly due to fouling. However, did you know that…
… self cleaning and self flushing systems are now available from Process Instruments for most types of sensors?
… these fouling removal systems can extend the life of sensors and drastically reduce maintenance regimes?
… Pi’s self cleaning/flushing systems are affordable, simple and trouble free by design?
Whatever the process being monitored is, there is often something in the sample water capable of fouling a sensor, and therefore causing erroneous results. The obvious solution to this problem is to clean the sensor, but how regular should inspection and cleaning programs be for each piece of instrumentation? Too regular and the inspection and cleaning regime is time consuming and unnecessarily costly. Not often enough and the instrumentation will give false results and probably fail prematurely.
Simple, reliable and easy to maintain, Process Instruments’ Autoclean/Autoflush systems are an alternative to mechanical cleaning mechanisms which can clog and break. By regularly spraying the sensor/probe with clean water or air, the sensor remains clean and free from fouling for extended periods of time. The sensor cleaning cycle is activated by Pi’s controller for a user selectable length of time and frequency so that no matter how dirty the application, the probe remains clean. With no moving parts in the sensor body or in the cleaning attachment there is nothing to replace or check other than a simple valve positioned in an easy to reach location.
Pi’s Autoclean and Autoflush systems can give trouble free and fouling free functioning of sensors for weeks, if not months, at a time.
This option can be added to our pH, ORP, Turbidity, Suspended Solids and Dissolved Oxygen (DO) sensors. Consisting of an end cap to direct the flow of clean water (or air for a DO sensor) across the face of the sensor blasting any dirt away. The cleaning is controlled by a single valve positioned in an easily accessible location.
If using air to clean a DO sensor the system can also automatically verify that the sensor is still responding correctly, removing any need to remove the sensor from the sample for months at a time.
For sensors that require flow cell mounting like Chlorine, Ozone and Chlorine Dioxide, an Autoflush system has inbuilt valves which automatically start/stop the sample flow and control the flow of clean water past the probe. The user can set the flushing interval and duration to keep the flow cell and sensor clear from fouling. For particularly dirty or stubborn contaminants, warm water can be used as the flush water to aid cleaning.
With the above options, whatever the application or parameter being measured, Process Instruments will be able to provide a monitoring system that will not only be accurate, precise and long lasting but that will also remain free from fouling and save the operator both time and money.
Click on the following for help
> Help with your application
> Technical help with your Analyser
> Help choosing a product
Following on from the success of numerous water treatment plants in the UK and Ireland, Pi is now beginning to offer the CoagSense coagulation controller to other countries in the
Chlorine analysers identical to those already installed on some of their customer’s sites in Lisbon, Portugal, were chosen by Pi’s distributor for Portugal and Spain, Izasa Scientific, as part of
Norwegian companies continue to innovate in many industries such as aquaculture and wastewater treatment, and Pi’s distributor has recently been exploring ways in which Pi’s technology can be applied to
